1. Produk Lebihview
The Tamiya 86005 Black Paint Spray is specifically formulated for decorating transparent polycarbonate bodies used in R/C car modeling. This paint provides a durable, oil-resistant finish suitable for both electric and gas-powered R/C bodies.
Image 1.1: Tamiya 86005 Black Paint Spray can. This 100ml aerosol can contains black, gloss-finish paint designed for polycarbonate surfaces.
Fitur Utama:
- Black colored paint.
- Intended for polycarbonate R/C bodies.
- Can be used on gas-powered R/C bodies.
- Impervious to oil and fuels.
- Gloss finish.
- Tahan air.
2. Informasi Keselamatan
PERINGATAN: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm (Proposition 65 warning). Always use in a well-ventilated area. Keep out of reach of children. Read all warnings on the product label before use.
- Gunakan hanya di area yang berventilasi baik. Hindari menghirup uap.
- Kenakan alat pelindung diri yang sesuai, seperti sarung tangan dan pelindung mata.
- Jauhkan dari panas, permukaan panas, percikan api, nyala api terbuka, dan sumber penyulutan lainnya. DILARANG MEROKOK.
- Wadah bertekanan: Jangan ditusuk atau dibakar, bahkan setelah digunakan.
- Jangan menyemprot pada api terbuka atau sumber penyalaan lainnya.
- Lindungi dari sinar matahari. Jangan sampai terkena suhu melebihi 50°C (122°F).
- Buang isi/wadah sesuai dengan peraturan setempat.
- Note: Never use these paints on plastic models other than polycarbonate.
3. Persiapan dan Pengaturan
3.1 Workspace Preparation
- Ensure your workspace is clean, dust-free, and well-ventilated.
- Cover surrounding areas to protect them from overspray.
- Maintain an ambient temperature between 20-25°C (68-77°F) for optimal results.
3.2 Persiapan Permukaan
- Clean the polycarbonate R/C body thoroughly with mild soap and water to remove any dirt, grease, or mold release agents.
- Rinse the body completely and allow it to dry fully.
- For best adhesion, lightly scuff the inside surface of the polycarbonate body with a fine-grit abrasive pad (optional, but recommended for maximum durability).
- Mask off any areas you do not wish to paint using painter's tape or liquid mask. Remember to paint the body from the inside.
3.3 Paint Can Preparation
- Shake the can vigorously for at least one minute after the mixing ball begins to rattle. Continue shaking periodically during application.
- Test spray on a scrap piece of polycarbonate or similar material to check spray pattern and color consistency.
4. Petunjuk Pengoperasian (Aplikasi)
- Hold the Can: Hold the spray can upright, approximately 30 cm (12 inches) from the surface of the polycarbonate body.
- Apply Light Coats: Apply the paint in thin, even coats. It is better to apply several thin coats than one thick coat to prevent runs and ensure proper adhesion.
- Goresan Tumpang Tindih: Begin spraying off the edge of the body and move across the surface in smooth, overlapping strokes. Release the nozzle at the end of each stroke.
- Pengeringan Antar Lapisan: Allow each coat to dry to the touch before applying the next. This typically takes 10-15 minutes, depending on humidity and temperature.
- Build Color: Continue applying thin coats until the desired color depth and opacity are achieved. For black, this may require 2-3 coats.
- Pengobatan: After the final coat, allow the paint to cure completely. The full cure time is approximately 24 hours. Avoid handling the painted body excessively during this period.
- Remove Masking: Once the paint is dry to the touch, carefully remove any masking tape or liquid mask.
Penting: Always paint the di dalam of the transparent polycarbonate body. This protects the paint from scratches and impacts during use.
5. Perawatan dan Penyimpanan
5.1 Can Maintenance
- After each use, invert the can and spray for a few seconds until only clear propellant comes out. This clears the nozzle and prevents clogging.
- Wipe the nozzle clean with a cloth.
5.2 Penyimpanan
- Store the paint can in a cool, dry place, away from direct sunlight and extreme temperatures.
- Ensure the cap is securely placed on the can to prevent accidental discharge or drying of the nozzle.
- Jauhkan dari jangkauan anak-anak dan hewan peliharaan.
6. Penyelesaian masalah
| Masalah | Kemungkinan Penyebab | Larutan |
|---|---|---|
| Uneven spray pattern / Clogging | Nozzle is clogged or paint not mixed properly. | Shake can vigorously. Clean nozzle by inverting can and spraying until clear, or by carefully removing and cleaning with a solvent (e.g., lacquer thinner). |
| Cat menetes atau mengalir | Too much paint applied in one coat, or can held too close. | Apply thinner, even coats. Maintain a distance of 30 cm (12 inches) from the surface. |
| Poor adhesion / Peeling paint | Surface not properly cleaned or prepared. Not for use on non-polycarbonate plastics. | Ensure surface is clean, dry, and free of contaminants. Confirm the material is polycarbonate. |
| Hasil akhir kusam | Insufficient coats or improper drying conditions. | Apply additional thin coats. Ensure proper ventilation and temperature during drying. |
7. Spesifikasi
| Merek: | TAMIYA |
| Nomor Model: | 86005 (TAM86005) |
| Warna: | Hitam |
| Jenis Selesai: | mengkilap |
| Volume Barang: | 100 Mililiter (3.38 Fl Oz) |
| Jenis cat: | Oil, Spray |
| Kegunaan Khusus: | R/C Car Polycarbonate Bodies |
| Rekomendasi Permukaan: | Plastic (Polycarbonate only) |
| Pemakaian Dalam/Luar Ruangan: | Di dalam ruangan (dengan ventilasi yang memadai) |
| Waktu Penyembuhan Penuh: | 24 Jam |
| Cakupan: | 0.1 to 0.15 square meters per coat |
| Tahan Air: | Tahan Air |
| UPC-nya: | 885109209505 |
8. Garansi dan Dukungan
Jaminan: This product is sold without a manufacturer's warranty. Please refer to the product packaging for any specific warranty information that may be provided by the retailer at the time of purchase.
Dukungan Pelanggan: For technical assistance or product inquiries, please contact Tamiya customer support directly through their official website or authorized distributors. Keep your product model number (86005) handy when contacting support.