Performance Tool W1614 2 Ton (4,000 lbs.) Capacity Floor Jack User Manual

Perkenalan

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Performance Tool W1614 2 Ton (4,000 lbs.) Capacity Floor Jack. Designed for heavy-duty lifting tasks, this floor jack is constructed from durable steel and features swivel rear casters for easy positioning. It has a maximum lifting capacity of 4,000 pounds and can reach a maximum height of 15 inches.

Figure 1: Performance Tool W1614 2 Ton Floor Jack.

Informasi Keselamatan

PERINGATAN: Produk ini dapat membuat Anda terpapar bahan kimia termasuk timbal, yang oleh Negara Bagian California diketahui dapat menyebabkan kanker dan cacat lahir atau gangguan reproduksi lainnya. Untuk informasi lebih lanjut, kunjungi www.P65Warnings.ca.gov.

Always read and understand all instructions and warnings before using this floor jack. Failure to follow these instructions may result in serious injury or property damage.

• Use on Hard, Level Surface: Always operate the jack on a hard, level surface capable of supporting the load.
• Use Jack Stands: This floor jack is a lifting device only. Immediately after lifting, support the vehicle with appropriate jack stands. Do not work under a vehicle supported only by a floor jack.
• Jangan Melebihi Kapasitas Terukur: Never exceed the 4,000 lbs. (2 Ton) rated capacity of this jack.
• Center Load on Saddle: Ensure the load is centered on the jack saddle to prevent slipping.
• Chock Wheels: Always chock the wheels that are not being lifted.
• Tetap Bersih: Jauhkan tangan, kaki, dan bagian tubuh lainnya dari bagian yang bergerak dan titik jepit.
• Periksa Sebelum Digunakan: Before each use, inspect the jack for any damage, leaks, or loose parts. Do not use if damaged.
• Perlindungan Beban Berlebih: This jack is equipped with an overload protection bypass valve for safety. Do not attempt to bypass or modify this feature.

Pengaturan dan Persiapan Awal

Before first use, or if the jack has been stored for an extended period, it is important to bleed any air from the hydraulic system to ensure proper operation. Air in the system can cause the jack to lift unevenly or not lift at all.

Mengeluarkan Udara dari Sistem Hidrolik:

1. Locate the release valve. This is typically a screw or knob that controls the lowering function.
2. Masukkan pegangan ke soket pegangan.
3. Putar gagang berlawanan arah jarum jam untuk membuka katup pelepas sepenuhnya.
4. Pump the handle fully up and down approximately 10-15 times to force any trapped air out of the system.
5. Putar pegangan searah jarum jam untuk menutup katup pelepas.
6. Test the jack by pumping the handle to raise the saddle. It should raise smoothly and evenly. If not, repeat the bleeding process.

Gambar 2: Sudut view of the floor jack, showing the handle socket and general structure.

Petunjuk Pengoperasian

Lifting a Vehicle:

1. Parkirkan kendaraan di permukaan yang keras dan rata. Aktifkan rem parkir dan ganjal roda yang akan tetap berada di tanah.
2. Locate the vehicle's manufacturer-recommended lifting points. Refer to your vehicle's owner's manual.
3. Position the floor jack so that the saddle is directly under the lifting point. Ensure the load is centered on the saddle.
4. Close the release valve by turning the handle clockwise until it is firmly closed. Do not overtighten.
5. Pump the handle up and down to raise the vehicle to the desired height. Lift only high enough to place jack stands.
6. Segera tempatkan dongkrak penyangga yang sesuai di bawah titik-titik penopang yang telah ditentukan pada kendaraan.
7. Slowly open the release valve by turning the handle counter-clockwise to lower the vehicle onto the jack stands. Once the vehicle is securely resting on the jack stands, remove the floor jack.

Lowering a Vehicle:

1. Ensure the area around the vehicle is clear of obstructions and personnel.
2. Position the floor jack saddle directly under the vehicle's lifting point, adjacent to the jack stands.
3. Pump the jack handle a few times to slightly raise the vehicle off the jack stands.
4. Lepaskan dongkrak penyangga dari bawah kendaraan dengan hati-hati.
5. Slowly turn the jack handle counter-clockwise to open the release valve. The vehicle will begin to lower. Control the lowering speed by adjusting how much you open the valve.
6. Once the vehicle is fully lowered, remove the floor jack.

Figure 3: Diagram showing key dimensions and lift range of the floor jack.

Pemeliharaan

• Pelumasan: Lumasi semua bagian yang bergerak secara berkala dengan oli mesin ringan.
• Cairan Hidrolik: Check the hydraulic fluid level regularly. If low, add high-quality hydraulic jack oil. Do not use brake fluid or other types of oil.
• Pembersihan: Jaga agar dongkrak tetap bersih dan bebas dari kotoran, minyak, dan serpihan.
• Penyimpanan: Store the jack in a dry, clean place with the ram fully retracted to prevent rust and extend seal life.
• Inspeksi: Regularly inspect for any signs of wear, damage, or leaks. If any issues are found, do not use the jack and have it serviced by qualified personnel.

Penyelesaian Masalah

Spesifikasi

Garansi dan Dukungan

For specific warranty information, please refer to the documentation included with your purchase or contact Performance Tool customer service. Keep your purchase receipt for warranty claims.

Panduan Pengguna resmi (PDF) tersedia untuk diunduh: Unduh Panduan Pengguna (PDF)

For technical support or inquiries, please visit the official Performance Tool websitus atau hubungi departemen layanan pelanggan mereka.