Faria 13795 Chesapeake Depth Sounder Thru-Hull Instruction Manual

1. Pendahuluan

This manual provides detailed instructions for the installation, operation, and maintenance of your Faria 13795 Chesapeake Depth Sounder Thru-Hull. This device is designed to provide accurate depth readings in various marine conditions, utilizing advanced microprocessor technology for reliable performance.

2. Informasi Keselamatan

• Selalu putuskan aliran listrik sebelum melakukan instalasi atau pemeliharaan apa pun.
• Ensure proper sealing of all thru-hull components to prevent water intrusion.
• Konsultasikan dengan teknisi kelautan yang berkualifikasi jika Anda ragu tentang langkah-langkah pemasangan apa pun.
• This device is an aid to navigation and should not be used as the sole source of navigation information.

3. Isi Paket

Verifikasi bahwa semua item ada dalam paket:

• Faria 13795 Chesapeake Depth Sounder Display Unit
• Thru-Hull Transducer (Note: The included transducer is typically 1.5 inches. A 2-inch transducer may need to be purchased separately if required for your application.)
• Perangkat Keras Pemasangan
• Instruksi Manual (dokumen ini)

4. Pengaturan dan Instalasi

Proper installation is crucial for accurate depth readings. This section outlines the general steps for installing the depth sounder and its thru-hull transducer.

4.1 Komponen Berakhirview

Gambar 1: Faria 13795 Depth Sounder display unit (left) and the thru-hull transducer (right). The display features an LCD screen, 'ON/OFF MODE' button, and up/down arrow buttons for navigation and settings adjustment.

4.2 Pemasangan Transduser

1. Pilih lokasi: Choose a location on the hull that is free from turbulence, air bubbles, and obstructions. The transducer should be mounted in an area that remains submerged at all speeds.
2. Lubang Bor: Carefully drill a hole of the appropriate diameter for the transducer shaft. Refer to the transducer's specific dimensions for precise hole size.
3. Aplikasikan Sealant: Apply a marine-grade sealant (e.g., 3M 5200) generously around the edge of the transducer flange that will contact the hull.
4. Masukkan Transduser: Insert the transducer from the outside of the hull into the drilled hole.
5. Secure Internally: From inside the boat, place the large rubber gasket around the transducer shaft, followed by the securing nut.
6. Kencangkan Mur: Hand-tighten the nut securely. Avoid over-tightening, which can damage the hull or transducer. Wipe away any excess sealant.
7. Rute Kabel: Route the transducer cable to the display unit, ensuring it is protected from abrasion and interference.

4.3 Pemasangan Unit Tampilan

1. Lokasi Pemasangan: Select a suitable location on the dashboard or panel for the display unit, ensuring clear visibility and accessibility.
2. Pembukaan Potongan: Use the provided template (if applicable) to cut the appropriate size opening for the display unit.
3. Secure Display: Insert the display unit into the opening and secure it using the supplied mounting bracket and hardware.
4. Pengkabelan:
   • Connect the transducer cable to the designated port on the display unit.
   • Connect the power wire (typically red) to a switched 12V DC power source.
   • Connect the ground wire (typically black) to a reliable ground point.
   • Pastikan semua sambungan aman dan terisolasi dengan benar.

5. Petunjuk Pengoperasian

This section details how to operate your Faria Depth Sounder.

5.1 Daya Hidup/Mati

• Untuk menghidupkan perangkat, tekan dan tahan tombol MODE HIDUP / MATI sampai layar menyala.
• Untuk mematikan unit, tekan dan tahan tombol MODE HIDUP / MATI tombol sampai layar mati.

5.2 Operasi Dasar

• Upon powering on, the unit will typically display the current depth.
• The unit features automatic gain control to optimize depth readings in varying conditions.
• Pencahayaan latar is integrated for enhanced visibility, especially during low-light conditions.

5.3 Mode Selection and Settings

• Tekan tombol MODE HIDUP / MATI button briefly to cycle through different display modes or access settings menus.
• Gunakan Up (▲) Dan Turun (▼) arrow buttons to adjust values or navigate menu options.
• Keel Offset: This setting allows you to adjust the depth reading to compensate for the distance between the transducer and the bottom of your boat's keel. Consult your boat's specifications to determine the correct offset value.
• Deep and Shallow Water Alarms: Set desired depth thresholds for both deep and shallow water. The unit will provide audio and visual alarms when these thresholds are crossed.

6. Fitur

• Oversized Back-lit display for clear visibility in various lighting conditions.
• Audio and visual alarms for elevation (deep and shallow water).
• Programmable keel offset for accurate depth measurement relative to the keel.
• Automatic gain control for optimal performance across different bottom conditions.
• Depth capability: 3-199 feet (61 meters).

7. Pemeliharaan

• Pembersihan: Wipe the display unit with a soft, damp kain. Hindari pembersih atau pelarut abrasif.
• Transducer Inspection: Periodically inspect the transducer for marine growth or damage. Clean gently with a soft brush if necessary. Ensure the transducer cable is free from kinks or damage.
• Koneksi: Check all electrical connections annually for corrosion or looseness.

8. Penyelesaian masalah

9. Spesifikasi

• Model: 13795
• Merek: Faria
• Kemampuan Kedalaman: 3-199 kaki (61 meter)
• Bahan: Plastik
• Berat Barang: Kira-kira 1 pon
• UPC-nya: 759266137950
• Persyaratan Daya: 12V DC (typical marine electrical system)
• Menampilkan: LCD dengan lampu latar

10. Garansi dan Dukungan

Faria products are manufactured to high standards. For specific warranty details, please refer to the warranty card included with your product or visit the official Faria Beede Instruments website. For technical support or service inquiries, please contact Faria customer service directly.