AKO CAMRegis Basic Owner’s Manual

AKO CAMRegis Basic

Peringatan

• Unit harus dipasang di tempat yang terlindung dari getaran, air, dan gas korosif, di mana suhu sekitar tidak melebihi nilai yang ditunjukkan dalam data teknis.
• For the unit to operate correctly, use only the probes supplied by AKO. For the reading to be correct, the probe should be used in a place without heat influences apart from the temperature you want to me-asure or control.
• Probe dan kabelnya TIDAK PERNAH dipasang di saluran bersama dengan kabel daya, kontrol, atau pengumpan.
• In the event of lengthening the NTC probe, always used shield cable and earth the mesh. In these cases, the maximum deviation will be 0.25 ºC from -40 ºC to +20 ºC (Maximum 1000 m with a minimum section of 0.5 mm2 ).
• We recommend using AKO-15586 cable. Always disconnect the power supply to do the wiring.
• The power circuit should be equipped with a switch marked as dis-connecting device of the equipment of at least 2 A, 230 V, situated near the appliance.
• The power supply cable should be H05VV-F or H05V-K type. The gauge will depend on local regulations, but should in no case be less than 1 mm2 . The electrical installation should be carried out under pipe. Using the logger not observing the manufacturer’s instructions may alter the appliance safety requirements. Only probes supplied by AKO should be used for the appliance to operate correctly.

Instalasi

DIMENSI

 Spesifikasi teknis

• Power supply……………………………………………… 90-240 V~ 50/60Hz
• Alarm relay…………………………………………………………… 8 A cos j=1
• NTC range (AKO-14931)…………………………………. -50 ºC to 99.9 ºC
• Range 4-20 mA…………. Configurable from -100 to 900 (1000 levels)
• Resolution ………………………………………………………………………..0,1
• Accuracy class (-40 ºC to 40 ºC):………………….. ±1 ºC acc/ EN 12830
• Response time:……………………………………………………. < 20 seconds
• Maximum relative time error:…………………………………………< 0.1 %
• Marked according to UNE-EN 12830……………..S,A,1,-40 ºC + 40 ºC
• ………………………………………………………… Cocok untuk digunakan dalam penyimpanan (S)
• …………………………………………………………..Tipe lingkungan iklim (A)
• ………………………………………………………………………….. Kelas akurasi (1)
• Maximum input power……………………………………………………8.5 VA
• Working ambient temperature…………………………………0 ºC to 40 ºC
• Storage ambient temperature……………………………… -20 ºC to 60 ºC
• Degree of protection…………………………………………………………IP40
• Insulasi ganda antara catu daya, sirkuit sekunder, dan keluaran relai.
• Installation category……………………………………… II acc/ EN 61010-1
• Pollution degree…………………………………………… II acc/ EN 61010-1
• Maintenance of date and time without power supply……Up to 2 days
• Internal buzzer………………………………………………….. 70dB at 30 cm
• SD cards accepted……………………………………SD/SDHC (FAT / FAT32)

 Pengkabelan

Operasi

Fungsi utama

• key: A short press displays the maximum value reached in the last 24h, and the time when all the active inputs were reached. In the programming menu it allows scrolling around the different levels, or during the setting of a parameter, changing its value.
• key: A short press displays the minimum value reached in the last 24h, and the time when all the active inputs were reached. In the programming menu it allows scrolling around the different levels, or during the setting of a parameter, changing its value.
• key: A short press downloads the data of the ongoing log onto the SD card (if it has been inserted)
• key: A short press downloads ALL the logged data onto the SD card (if it has been inserted). The save without changes, return to previous level or exit programming parameter appears on the programming menu.
• SET key: A short press downloads the data of the last log onto the SD card (if it has been inserted).
• Membungkam alarm akustik (menurut parameter P50).
• Dalam pemrograman, konfirmasikan pilihan dan simpan nilai yang dimasukkan.
•   keys : Pressing for over 10 seconds accesses the data log display menu.
• Tekan untuk memilih blok log dan tekan SET untuk mengaksesnya.
• Tekan  untuk memilih log yang akan ditampilkan, setelah 1 detik nilai dari setiap masukan akan ditampilkan, menunjukkan tanggal dan waktu log.
• N + O keys : Pressing for over 10 seconds accesses the alarms log display menu.
  Press N / Q to select the input to be displayed and press SET.
  Press N / Q to select the event to be displayed (no. 1 is the most recent event), after 1 second the value of each input will be displayed, indicating the date and time of the event.
• keys: Pressing them for over 10 seconds accesses the programming menu.

Struktur data yang dicatat

• Data yang dicatat disimpan dalam memori internal logger yang diatur dalam blok log. Periode waktu yang disimpan di setiap blok, dan kapasitas maksimum memori internal, bergantung pada interval log (parameter L1), seperti yang ditunjukkan pada tabel.
• Logger memiliki slot untuk kartu SD, yang memungkinkan mentransfer data yang disimpan untuk ditampilkan di komputer atau untuk disimpan sebagai cadangan. Data ini disimpan dalam format spreadsheet (.csv), diatur dengan cara berikut:

PENTING: Do not remove the SD card until the indicator turns off. The download may take several minutes depending on the data saved.

• Downloads ALL the logged data (P key)
  Dua files dihasilkan yang namanya tahun, bulan dan hari pengunduhan, dalam dua folder berbeda SEMUA dan ALARM. Yang pertama berisi file dengan semua data yang dicatat oleh perangkat hingga saat itu dan yang kedua berisi file dengan acara yang disimpan hingga saat itu (lihat bagian 5.2):
•  Log alarm
  This function saves an event whenever an alarm is activated or deactivated. To download the events log data, press the P key, all the data logged up to date are downloaded onto the SD card, including the events log, contained in the “ALARMS” folder.
•  Memulai awal
  Tanggal dan waktu akan diminta selama start-up pertama.

 Menu pemrograman (parameter)
To access the parameter programming menu, press the N + Q keys at the same time. Refer to the list of available parameters in section 5 of this manual. After 20 seconds without touching any key, the unit returns to the previous level. If it is in level 3 the changes will not be saved.

Tabel parameter dan pesan

Def. kolom menunjukkan parameter default pabrik. Kecuali dinyatakan lain, nilai suhu dinyatakan dalam ºC (suhu setara dalam ºF).