Avidsen 107101 Pocket Digital Multimeter User Manual

1. Informasi Keselamatan

Please read and understand all safety information before operating this device. Failure to follow these instructions may result in electric shock, fire, or damage to the device.

• Selalu pastikan multimeter berada pada fungsi dan rentang yang benar sebelum melakukan pengukuran.
• Jangan melebihi nilai input maksimum yang ditentukan untuk setiap rentang.
• Berhati-hatilah saat bekerja dengan sirkuit listrik yang aktif. Tegangan tinggitages bisa berbahaya.
• Periksa kabel uji apakah ada kerusakan sebelum setiap penggunaan. Jangan gunakan jika isolasi rusak.
• This device features double insulation for enhanced safety.
• Do not operate the multimeter if it appears damaged or if the casing terbuka.
• Jauhkan perangkat dari air dan kelembapan.

2. Produk Lebihview

The Avidsen 107101 is a compact, pocket-sized digital multimeter designed for various electrical measurements. It features a 3.5-digit display for clear readings and comes with two insulated test probes.

Image: Avidsen 107101 Pocket Digital Multimeter with its test leads.

Fitur Utama:

• Mengukur AC/DC Voltage
• Measures DC Current
• Measures Resistance
• Diode Test Function
• Transistor Gain (hFE) Measurement
• 50 Hz Square Wave Generator
• 3.5-digit, 0.5-inch Digital Display
• Isolasi Ganda

3. Pengaturan

Pemasangan Baterai:

The Avidsen 107101 multimeter operates on a 12V battery (Type 23A). To install or replace the battery:

1. Pastikan multimeter dimatikan dan kabel uji dilepas.
2. Temukan penutup ruang baterai di bagian belakang perangkat.
3. Carefully remove the screw(s) securing the cover and open it.
4. Insert the 12V (Type 23A) battery, observing the correct polarity (+ and -).
5. Pasang kembali penutup kompartemen baterai dan kencangkan dengan sekrup.

Menghubungkan Kabel Uji:

Connect the red and black test leads to the appropriate input jacks on the multimeter. The black lead typically connects to the 'COM' (common) jack, and the red lead connects to the 'VΩmA' jack for most measurements.

4. Petunjuk Pengoperasian

To operate the multimeter, turn the rotary switch to the desired function and range. The display updates measurements approximately twice per second.

4.1. Volt AC/DCtage Pengukuran:

1. Hubungkan kabel uji hitam ke jack 'COM' dan kabel uji merah ke jack 'VΩmA'.
2. Turn the rotary switch to the desired ACV (Alternating Current Voltage) atau DCV (Tegangan Arus Langsung)tage) range. Select a range higher than the expected voltage.
3. Hubungkan probe uji secara paralel di seluruh rangkaian atau komponen yang akan diukur.
4. Baca vol.tagnilai e pada tampilan digital.

4.2. Pengukuran Arus DC:

1. Hubungkan kabel uji hitam ke jack 'COM' dan kabel uji merah ke jack 'VΩmA'.
2. Turn the rotary switch to the desired DCA (Direct Current Amperage) range.
3. Penting: Connect the test probes in series with the circuit. Break the circuit and insert the multimeter.
4. Baca nilai saat ini pada tampilan digital.

4.3. Pengukuran Resistansi:

1. Hubungkan kabel uji hitam ke jack 'COM' dan kabel uji merah ke jack 'VΩmA'.
2. Turn the rotary switch to the desired Ω (Ohms) range.
3. Penting: Pastikan rangkaian atau komponen tersebut telah dimatikan dayanya sebelum mengukur resistansi.
4. Hubungkan probe pengujian di seluruh komponen yang akan diukur.
5. Baca nilai resistansi pada tampilan digital.

4.4. Uji Dioda:

1. Hubungkan kabel uji hitam ke jack 'COM' dan kabel uji merah ke jack 'VΩmA'.
2. Turn the rotary switch to the diode symbol (usually a triangle with a line).
3. Hubungkan probe merah ke anoda dan probe hitam ke katoda dioda. Layar akan menampilkan tegangan maju.tagjatuh.
4. Balikkan probe. Layar akan menampilkan 'OL' (Overload) untuk dioda yang baik.

4.5. Transistor Gain (hFE) Measurement:

This function allows you to measure the DC current gain (hFE) of NPN and PNP transistors.

1. Turn the rotary switch to the 'hFE' position.
2. Identify the Emitter (E), Base (B), and Collector (C) terminals of the transistor.
3. Insert the transistor leads into the corresponding sockets in the hFE test socket on the multimeter, ensuring correct NPN or PNP type selection.
4. Read the hFE value on the digital display.

4.6. 50 Hz Square Wave Generator:

The multimeter can generate a 50 Hz square wave signal for testing purposes.

1. Turn the rotary switch to the '50Hz Square Wave' position.
2. The square wave output will be available at the 'VΩmA' and 'COM' jacks.
3. Connect an oscilloscope or other suitable device to observe the generated waveform.

5. Pemeliharaan

Pembersihan:

Bersihkan perangkat dengan iklanamp cloth and a mild detergent. Do not use abrasive cleaners or solvents. Ensure the device is dry before use.

Penyimpanan:

When not in use for extended periods, remove the battery to prevent leakage. Store the multimeter in a cool, dry place, away from direct sunlight and extreme temperatures.

6. Penyelesaian masalah

• Tidak Ada Tampilan: Periksa pemasangan baterai dan pastikan baterai memiliki daya yang cukup. Ganti jika perlu.
• 'OL' or '1' on Display: This indicates an overload or out-of-range measurement. Select a higher range or check for an open circuit.
• Bacaan yang Salah: Verify the correct function and range are selected. Ensure test leads are properly connected and not damaged. Check the battery level.
• No Square Wave Output: Ensure the function is correctly selected and connections are secure.

7. Spesifikasi

8. Garansi dan Dukungan

For warranty information and technical support, please refer to the documentation included with your purchase or visit the official Avidsen websitus. Simpan bukti pembelian Anda untuk klaim garansi.

Pabrikan: Avidsen

Weblokasi: www.avidsen.com (Mantanample link, please verify actual manufacturer weblokasi)