ORIA Motion Sensor Light User Manual

1. Pendahuluan

Terima kasih sudah membeliasing the ORIA Motion Sensor Light. This battery-powered LED night light is designed to provide convenient, automatic illumination in various areas of your home. Please read this manual carefully before installation and use to ensure proper operation and longevity of your device.

2. Isi Paket

• 3 x ORIA Motion Sensor Night Light
• 6 x Sekrup
• 1 x Pita Perekat Dua Sisi
• 1 x Panduan Pengguna

3. Spesifikasi

4. Informasi Keselamatan

• Jangan mencampur baterai lama dan baru.
• Jangan mencampur baterai alkaline, standar (karbon-seng), atau baterai isi ulang (nikel-kadmium).
• Pastikan baterai dimasukkan dengan polaritas yang benar (+ dan -).
• Remove batteries if the light will not be used for an extended period.
• Perangkat ini hanya untuk penggunaan di dalam ruangan.
• Jangan terkena air atau kelembapan berlebihan.
• Jauhkan dari jangkauan anak-anak.

5. Pengaturan

5.1 Pemasangan Baterai

1. Putar perlahan penutup belakang lampu berlawanan arah jarum jam untuk membuka ruang baterai.
2. Insert 3 AAA batteries (not included) into the compartment, ensuring correct polarity.
3. Replace the back cover by aligning the marks and twisting clockwise until secure.

5.2 Opsi Pemasangan

The ORIA Motion Sensor Light offers two installation methods:

Image: Demonstrates the two installation methods: using screws for a permanent fixture or double-sided adhesive tape for a temporary, non-damaging mount.

Opsi 1: Pemasangan Sekrup

• Choose a desired location for the light.
• Mark the positions for the two screw holes on the mounting surface.
• Bor lubang pilot jika perlu.
• Secure the light to the surface using the provided screws.

Option 2: Adhesive Tape Mounting

• Clean and dry the desired mounting surface thoroughly.
• Peel off one side of the double-sided adhesive tape and apply it firmly to the back of the light.
• Peel off the other side of the tape and press the light firmly onto the mounting surface for at least 30 seconds.
• Allow 24 hours for the adhesive to fully cure before applying significant pressure.

6. Petunjuk Pengoperasian

The ORIA Motion Sensor Light features three operating modes: ON, OFF, and AUTO.

Image: Illustrates the light's behavior: off during daylight, activating upon motion detection, and automatically turning off after 30 seconds of no motion.

6.1 Pemilihan Mode

Locate the switch on the side of the light to select your desired mode:

• DI: The light will remain continuously on, regardless of ambient light or motion.
• MATI: Lampu akan tetap mati.
• AUTO (Motion Sensor Mode): The light will automatically turn on when motion is detected in a dark environment. It will turn off approximately 30 seconds after motion ceases.

6.2 Fungsionalitas Sensor Gerak

Image: A motion sensor light mounted on a wall, illuminating a staircase as a person ascends, demonstrating its practical application.

• Sudut Deteksi: 120 derajat
• Jarak Deteksi: Hingga 9.8 kaki (3 meter)
• The sensor is designed to activate only in low-light conditions to conserve battery life.
• Avoid placing the light in direct sunlight or near heat sources, as this may affect sensor performance.

7. Pemeliharaan

• Pembersihan: Wipe the light with a soft, dry cloth. Do not use abrasive cleaners or immerse in water.
• Penggantian Baterai: When the light dims or fails to activate, replace all 3 AAA batteries with new ones. Ensure correct polarity.
• Perawatan Sensor: Keep the motion sensor lens clean and unobstructed for optimal performance.

8. Penyelesaian masalah

9. Garansi dan Dukungan

ORIA products are designed for reliability and performance. For warranty information or technical support, please refer to the contact details provided with your purchase or visit the official ORIA weblokasi.

Harap simpan manual ini untuk referensi di masa mendatang.