Panduan Pemilik Unit Komputasi Tepi Cerdas M5STACK Unit C6L

Panduan Pemilik Unit Komputasi Tepi Cerdas M5STACK Unit C6L
Panduan Pengguna Driver Disk DOMUS LINE EASi DISK D Motion Control Disc

1. GARIS

Unit C6L is an intelligent edge computing unit integrated with the M5Stack_Lora_C6module — featuring an Espressif ESP32-C6 SoC and Semtech SX1262 LoRa transceiver — and engineered with a modular design for long-range, low-power LoRaWAN communication alongside high-speed 2.4 GHz Wi-Fi and BLE connectivity.
It includes a 0.66″ SPI OLED display for real-time data visualization, a WS2812Caddressable RGB LED for system-status indication, a built-in buzzer for audible alerts, and front-panel buttons (SYS_SW) with a reset switch for local interaction. Astandard Grove I²C interface allows seamless integration with M5Stack hosts and various Grove sensors. The onboard USB Type-C port supports ESP32- C6 firmware programming, serial debugging, and 5 V power input, while automatic power switching and multi-channel ESD/surge protection ensure stable operation. Unit C6L excels at real-time data acquisition, edge-intelligence processing, and remote control, making it ideal for IoT applications such as smart agriculture, environmental monitoring, industrial IoT, smart buildings, asset tracking, and urban infrastructure sensing.\

1.1. Satuan C6L

  1. Kemampuan Komunikasi
    Integrated LoRa (Semtech SX1262), supporting LoRaWAN Class A/B/Candpointto-point modes 2.4 GHz Wi-Fi and BLE via ESP32-C6-MINI-1U
  2. Prosesor & Performa
    Main Controller: Espressif ESP32-C6 (single-core RISC-V, up to 40 MHz) On-chip Memory: 512 KB SRAM with integrated ROM
  3. Manajemen Daya & Energi
    Power Input: USB Type-C (5 V input) and Grove 5 V input
  4. Tampilan & Indikator
    0.66″ SPI OLED display for real-time data visualization and status monitoringWS2812C addressable RGB LED for system-status indication Built-in buzzer for audible alerts
  5. Interfaces & Controls
    Grove I²C interface (with 5 V power) for seamless connection to M5Stack hostsandGrove sensors USB Type-C port for firmware programming, serial debugging, and power input Front-panel buttons (SYS_SW) and reset switch (MCU_RST) for local control
  6. Expansion & Debug Pads
    Bootloader pad: predefined jumper pad for entering bootloader mode Test points (TP1–TP8) for signal probing and in-circuit debug

2. SPESIFIKASI

Parameter Spesifikasi
MCU Espressif ESP32-C6 (RISC-V inti tunggal, hingga 40 MHz)
Komunikasi LoRaWAN; 2.4 GHz Wi-Fi BLE
Masukan Daya USB Tipe-C (5V) dan Grove 5V
Volume Pasokantage 3.3 V (LDO terpasang)
Penyimpanan Flash Flash SPI 16 MB (128 Mbit)
Menampilkan 0.66”SPI OLED(128×64)
Indikator                                  LED RGB yang dapat dialamatkan WS2812C
Bel Bel di dalam pesawat
Tombol System button (SYS_SW)and reset button(MCU_RST)
Antarmuka Grove I²C;USB Tipe-C;bantalan bootloader;bantalan debug TP1-TP8
Antena Kelas 2×SSMB-JEFamp konektor;2×konektor antena IPEX-4
Suhu Operasional Suhu Operasional
Fitur Tambahan Multi-channel ESD/surge protection
Pabrikan M5Stack Technology Co., Ltd Block A10, Expo Bay South Coast, Fuhai Street, Bao’an District, Shenzhen, China
Rentang Frekuensi untuk CE 2.4G Wi-Fi: 2412-2472MHz BLE: 2402-2480MHz Lora: 868-868.6MHz
EIRP Maksimum untuk CE BLE: 5.03dBm 2.4G Wi-Fi: 16.96dBm Lora: 9.45dBm
kategori penerima The equipment provider declared that the receiver category for the EUTis2.
2.1 Ukuran Modul
Ukuran Modul

3. Peringatan FCC

Perhatian FCC:
Perubahan atau modifikasi apa pun yang tidak disetujui secara tegas oleh pihak yang bertanggung jawab atas kepatuhan dapat membatalkan kewenangan pengguna untuk mengoperasikan peralatan. Perangkat ini mematuhi bagian 15 dari Peraturan FCC. Pengoperasian tunduk pada dua kondisi berikut: (1) Perangkat ini tidak boleh menimbulkan gangguan yang berbahaya, dan (2) perangkat ini harus menerima gangguan apa pun yang diterima, termasuk gangguan yang dapat menyebabkan pengoperasian yang tidak diinginkan.
CATATAN PENTING:
Catatan: This equipment has been tested and found to comply with the limits for a ClassBdigital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
perbaiki interferensi dengan satu atau lebih tindakan berikut:

  • Ubah arah atau pindahkan antena penerima.
  • Increase the separation betweentheequipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator&your body.
Instalasi Arduino

I. Installing Arduino IDE(https://www.arduino.cc/en/Main/Software)
Klik untuk mengunjungi situs resmi Arduino websitus, dan pilih paket instalasi untuk Anda
operating system to download. Ⅱ. Installing Arduino Board Management
1. Manajer Dewan URL is used to index the development board information for specific platform. In the Arduino IDE menu, select File -> Preferensi
Instalasi Arduino

2.Salin manajemen papan ESP URL di bawah ke Manajer Dewan Tambahan
URLs: field, and save.
https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
Instalasi Arduino
Instalasi Arduino

3. Di bilah sisi, pilih Board Manager, cari ESP, dan klik Instal.
Instalasi Arduino

4. Di bilah sisi, pilih Board Manager, cari M5Stack, lalu klik Instal.
Depending on the product used, select the corresponding development board under
Tools -> Board -> M5Stack -> {ESP32C6 DEV Module board}.
Instalasi Arduino

5. Hubungkan perangkat ke komputer Anda dengan kabel data untuk mengunggah program

M5STACK Logo

Dokumen / Sumber Daya

Unit M5STACK C6L Unit Komputasi Tepi Cerdas [Bahasa Indonesia:] Panduan Pemilik
M5UNITC6L, 2AN3WM5UNITC6L, Unit C6L Unit Komputasi Tepi Cerdas, Unit C6L, Unit Komputasi Tepi Cerdas, Unit Komputasi Tepi, Unit Komputasi, Unit

Referensi

Tinggalkan komentar

Alamat email Anda tidak akan dipublikasikan. Bidang yang wajib diisi ditandai *