XTOOL XTS500 Wireless Diagnostics Module User Manual

Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
Plug the USB wireless receiver into the USB port of the PC.
Go to the Wi-Fi selection page of your PC. Select WLAN 2 and search for the Wi-Fi hotspot with the same name as the SN of the device.
Once connected, your PC has established a connection with the device.

Koneksi Kabel

Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
Connect the VCI and the diagnostic PC with a USB Type-C cable.

Tindakan Pencegahan untuk Diagnosis

Ensure proper connections are made and follow safety protocols while performing diagnostics on vehicles.

About J2534 Toolbox
To install J2534 Toolbox:

Pindai kode QR atau kunjungi
https://www.xtooltech.com/english/DownloadCenter.html to find the installation pack.
Ekstrak file yang diunduh file and run Setup.exe. Follow the installation process.
After installation, restart your PC for changes to take effect.

Cara Penggunaan
To use J2534 Toolbox:

For wired connection: Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will detect the device automatically.
If not detected, click the Refresh button to try again.
For wireless connection: Plug in the WiFi Receiver, click the WiFi button, select WLAN 2, find the matching hotspot, and connect.
Ensure a stable connection before proceeding with diagnostics.

Merek Dagang
XTOOL is a trademark of Shenzhen Xtooltech Intelligent Co., Ltd. Copyright, registered in China, the United States, and other countries. All other marks are trademarks or registered trademarks of their respective holders.

Penafian Jaminan dan Batasan Kewajiban
All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Xtool reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given for the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Xtool will not be liable for any direct, special, incidental, or indirect damages, or for any economic consequential damages (including the loss of profits) as a result of using this product.

Before operating or maintaining this unit, please read this manual carefully, please pay extra attention to the safety warnings and precautions.

Dukungan & Layanan

Resmi Weblokasi: www.xtooltech.com
E-mail: xtoolinplusus@outlook.com

Pengenalan Umum

Prospek & Pelabuhan

OBDII-16 port: Connect to vehicle’s DLC port.
Nameplate: Show device information.
Type-C Port: Connect the device to diagnosis PC via wire.
Indicator Light: Show device status.

Warna Lampu Indikator	Arti Lampu Indikator
Lampu hijau pekat	Diberdayakan
Lampu hijau berkedip	Pembaruan firmware
Cahaya biru pekat	Device connected (no communication)
Lampu biru berkedip	Communicating with the vehicle
Lampu merah berkedip	Kesalahan perangkat

Memulai

Koneksi Kendaraan Vehicle

Koneksi Nirkabel

Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
Plug the USB wireless receiver into the USB port of the PC.
Go to Wi-Fi selection page of your PC. Select “WLAN 2”, and search for the Wi-Fi hotspot that has the same name as the SN of the device.
Once the hotspot is connected, your PC has established connection with the device.

Koneksi Kabel

Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
Connect the VCI and the diagnostic PC with a USB Type-C cable.

Tindakan Pencegahan untuk Diagnosis

volumetagKisaran e pada mobil: +9~+36V DC;
When testing some special functions, the operator must operate according to the prompts and meet the test conditions. In some cases, the conditions that need to be met are: engine water temperature 80 ℃~105 ℃, turn off headlights and air conditioners, keep the accelerator pedal in the released position, etc.;
Sistem kendali elektronik dari berbagai model sangat rumit. Jika Anda menghadapi situasi di mana pengujian tidak mungkin dilakukan atau sejumlah besar data pengujian tidak normal, Anda dapat mencari ECU kendaraan dan memilih menu model pada pelat nama ECU;
Hanya kabel yang disediakan oleh XTOOL dan dirancang untuk perangkat ini yang diizinkan untuk digunakan dengan perangkat ini guna menghindari kerusakan pada kendaraan atau perangkat tersebut;
When running a diagnostics session, DO NOT shut down the device directly. You should cancel the task before returning to the main interface and then shutting down the device.

About J2534 Toolbox
J2534 Toolbox is a PC application that manage the updates and operation logs for all VCIs that supports J2534 function. Before you start working on diagnostics with your PC, make sure you have the J2534 Toolbox installed.

Instalasi

Scan the QR code on the right, or go to:https://www.xtooltech.com/english/DownloadCenter.html
And find “J2534 Toolbox” for the installation pack.
After the download is completed, unzip it and click “Setup.exe”, then follow the installation process. We suggest you to restart your PC after installation.

Cara Penggunaan

The picture on the right shows the main screen of the J2534 Toolbox when the VCI is not connected to the diagnostic PC.

Device Connection – Wired

Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will automatically detect the device when you connect it.
If the status has not been refreshed after you connect the VCI via wire, click the Refresh button to try again.

Device Connection – Wireless

Plug in the WiFi Receiver that comes with the VCI box.
Click the WiFi button on the bottom-left corner and select “WLAN 2” (or other numbers)
Find the hotspot that names the same as the SN of the VCI box and click “Connect”.
When the connection is ready, you are OK to go.

Layar Utama
When the VCI is connected, you will see this screen:

SN: Shows the SN of the current VCI.
Firmware Version: Shows current firmware version that is installed on the VCI.
Driver Version: Shows current driver version that is installed on the VCI.
J2534 Authorization: Shows the VCI authorization status of current VCI.

Log Record: Turn on/off the J2534 communication logs recording.
Feedback: Send feedback to XTool customer service team when you meet any issues regarding the J2534 connection.

Firmware/Driver Update

If there is an update for the firmware or the driver, you will see a red dot beside the version number. Click the Update button on the right to check updates.
You can choose the version first, and click “Upgrade” button on the right to start updates.
DO NOT DISCONNECT THE VCI WHEN THE UPDATE IS IN PROGRESS!

Pengaturan

Click the “Settings” button on the top-right corner and go to the Toolbox settings.
Languages: Click to change language shown on the Toolbox.
Version Number: Check the updates of the Toolbox.
Log Cache: Show the size of the log folder. You can click the button on the right to clear all logs.
Save Location: This shows the location of the log folder. You can click this to get into the folder.

DoIP Mode Switch: When there are cases that the vehicle asks for a DoIP connection, please turn on the switch to enable DoIP mode. Please note that the DoIP mode can only be enabled in wired connection.

Masukan

If you meet any issues regarding J2534 connection, please record the logs (turn on the log recording switch) and send the logs to XTool customer service team. To better locate your problems, we need the following information in the report:

Alamat email Anda
Catatan files, recorded when the issues happened
Vehicle information (brand, model, MY)
Firmware/Driver version info
A brief description on what is going on (you can also attach images & screenshots)

Our customer service team will handle this and reply to you via email.

Kepatuhan FCC

FCC ID: 2AW3IV01W2

Perangkat ini mematuhi Bagian 15 Peraturan FCC. Pengoperasiannya tunduk pada dua kondisi berikut:

Perangkat ini mungkin tidak menimbulkan gangguan yang berbahaya
Perangkat ini harus menerima segala gangguan yang diterima, termasuk gangguan yang dapat menyebabkan pengoperasian yang tidak diinginkan.

Peringatan
Perubahan atau modifikasi yang tidak secara tegas disetujui oleh pihak yang bertanggung jawab atas kepatuhan dapat membatalkan kewenangan pengguna untuk mengoperasikan peralatan.

Catatan
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Ubah arah atau pindahkan antena penerima.
Tingkatkan pemisahan antara peralatan dan penerima.
Hubungkan peralatan ke stopkontak di sirkuit yang berbeda dari yang terhubung ke penerima.
Hubungi dealer atau teknisi radio/TV yang berpengalaman untuk mendapatkan bantuan.

Pihak yang Bertanggung Jawab

Nama Perusahaan: FCC US Agent, LLC
Alamat: 3722 Illinois Avenue, Saint Charles, IL, 60174, AS
E-mail: Dukungan@FCCUSAgent.com

Pernyataan ISED

IC: 29441-V01W2
Model: XTS500
PMN: V120，XTS500
HVIN: V01W2A

Perangkat ini berisi pemancar/penerima yang dikecualikan dari lisensi yang mematuhi RSS(s) pengecualian lisensi Inovasi, Sains, dan Pengembangan Ekonomi Kanada. Pengoperasian tunduk pada dua kondisi berikut:

Perangkat ini mungkin tidak menimbulkan gangguan.
Perangkat ini harus menerima gangguan apa pun, termasuk gangguan yang dapat menyebabkan pengoperasian perangkat yang tidak diinginkan.

Deklarasi kesesuaian
Dengan ini, Shenzhen XTOOLtech Intelligent Co., Ltd. menyatakan bahwa Modul Diagnostik Nirkabel ini telah memenuhi persyaratan utama dan ketentuan terkait lainnya dari Direktif 2014/53/EU. Sesuai dengan Pasal 10(2) dan Pasal 10(10), produk ini diizinkan untuk digunakan di semua negara anggota Uni Eropa.

Inggris Raya

Dengan ini, Shenzhen XTOOLtech Intelligent Co., Ltd menyatakan bahwa Modul Diagnostik Nirkabel ini memenuhi semua regulasi teknis yang berlaku untuk produk dalam lingkup Peraturan Peralatan Radio Inggris (SI 2017/1206); Peraturan Peralatan Listrik (Keselamatan) Inggris (SI 2016/1101); dan Peraturan Kompatibilitas Elektromagnetik Inggris (SI 2016/1091) dan menyatakan bahwa aplikasi yang sama belum diajukan ke Badan yang Disetujui Inggris lainnya.
Shenzhen Xtooltech Cerdas Co, Ltd.
Tambahkan: 17&18/F, Gedung A2, Kota Kreatif, Liuxian Avenue, Distrik Nanshan, Shenzhen, Cina
Kantor Pusat Shenzhen Telp: +86 755 2399608
E-mail: pemasaran@xtooltech.com

Tanya Jawab Umum

What operating system does XTS500 J2534 support?

The device only support Windows 7/8/10/11 or later version.

Why can’t my Mac recognize this device?

The device does not support macOS system.

Does the device need to be activated for usage?

This device need no S/N or activation code to activate the device. It will work directly with OE software once connection.

What functions can this device achieve?

This device can do what OE dignostic software do. Please check the compatibility before usage.

Dose the device include OE software?

OE software is not included in the package. You need to subscribe the OE software from manufacturer.

Dokumen / Sumber Daya

XTOOL XTS500 Wireless Diagnostics Module [Bahasa Indonesia:] Panduan Pengguna
XTS500 Wireless Diagnostics Module, XTS500, Wireless Diagnostics Module, Diagnostics Module, Module

Referensi

Panduan Pengguna

XTOOL XTS500 Wireless Diagnostics Module

Spesifikasi

Petunjuk Penggunaan Produk